Author Topic: New Way to Control Heat in 2D Materials  (Read 216 times)

Offline saikat07

  • Hero Member
  • *****
  • Posts: 513
  • Test
    • View Profile
    • My Web Address
New Way to Control Heat in 2D Materials
« on: November 26, 2016, 07:31:43 PM »
Two-dimensional (2D) materials such as those made from transition metal dichalcogenides (TMDs) are  layered one on top of another to create devices that could potentially be used for electronics. In fact, how these materials are layered determines to a large extent the electronic properties of the final device.

One property that engineers have kept in mind when plotting the layering of TMDs and other 2D materials is how they dissipate heat. Researchers at North Carolina State University, the University of Illinois at Urbana-Champaign (UI) and the Toyota Research Institute of North America (TRINA) have discovered an almost counterintuitive phenomenon in the layering of 2D materials that should help them to dissipate heat when they are fabricated into electronic devices.

In research described in the journal Nature Communications, the researchers wanted to address the issue of the difference in how heat is conducted in the strong, horizontal “in plane” bonds of the layers versus the weak, “out of plane” bonds between the layers. What they discovered was that in TMDs, heat was conducted at 100 watts per meter per Kelvin (W/mK) in plane, but at only 2 W/mK out of plane. This gives the TMDs a “thermal anisotropy ratio” of about 50. Anisotropy is when a material has a physical property that is different in one direction versus another. For instance, wood is stronger along its grain rather than against it.

The researchers wanted to see if they could increase these 2D materials’ heat conduction ratio to an even higher number. That would almost guarantee that the heat would travel in plane—along the layer—rather than between the layers.

To accomplish this, they added a few lithium ions between layers of molybdenum disulfide (a TMD). Two key changes were observed: First, it put the two layers out of alignment; and, second, it forced the atoms of molybdenum disulfide to rearrange. Those molecular adjustments were sufficient to yield an in-plane thermal conductivity of 45 W/mK and an out-of-plane thermal conductivity of only 0.4 W/mK. In other words, the thermal anisotropy ratio rose from 50 to more than 100.

Curiously, the number of lithium ions they struck upon was just right; in iterations of the experiment when they added more or fewer lithium ions, the result was actually a dip in the material’s thermal anisotropy ratio. But this taught them that the change in heat conductivity was tunable.
Senior Lecturer,
Department Of Electrical and Electronic Engineering
Faculty of Engineering,
Daffodil International University.

Offline shalauddin.ns

  • Sr. Member
  • ****
  • Posts: 364
  • Test
    • View Profile
Re: New Way to Control Heat in 2D Materials
« Reply #1 on: January 22, 2017, 07:54:15 PM »
Good to know.

Offline ZER

  • Full Member
  • ***
  • Posts: 101
    • View Profile
    • Department of Electrical and Electronic Engineering
Re: New Way to Control Heat in 2D Materials
« Reply #2 on: April 20, 2017, 01:41:08 PM »
Heat control is a very important issue while working on nanostructures. Because you have a very small confined space and a lot of electrons and high conductivity. Right Sir? :)
Md Zubair Ebne Rafique
Lecturer
Member Thesis Committee
Department of Electrical and Electronic Engineering
Faculty of Engineering
Daffodil International University (DIU)
Room # 506, Desk#G, 4th Floor, Main Campus
102, Shukrabad, Dhaka -1207
Contact# +8801685635425

Offline Abid Anjum Sifat

  • Jr. Member
  • **
  • Posts: 74
  • Test
    • View Profile
Re: New Way to Control Heat in 2D Materials
« Reply #3 on: April 20, 2017, 04:22:22 PM »
2D material is eventually becoming a great research intent.  :) :)